Wax Wrap — Video B: Flange · Script & Shot List

i Overview

Deliverable

Video B — flange (primer + putty + wax); 1 of 2 Wax Wrap videos

Length

~70 seconds, 12 beats (the fuller, flagship cut)

Subject

Steel pipe + 3-leg tee + bolted flanges in dark studio void; cutaway / iso camera

Material states (3D)

bare steel → brown primer → grey putty → wax wrap

Formats

9:16 · 16:9 · 1:1 · stills / exploded diagrams

Sources

5 mandated steps (sell sheet p.5) · locked specs · installer narration

Two expert value-adds woven in from the installer's own narration (prove we studied the footage): putty softens with the heat of your hands, and the end-flaps-down finish (3→9 o'clock) for water runoff + backfill protection.

1 Voiceover Script

display = on-screen / spoken words · tts = phonetic spelling fed to ElevenLabs (captions render the clean form). Numbered STEP rows are Carrie's five mandated steps.

#	Voiceover (display)	TTS hint
1	Lasting corrosion protection for pipes, valves, and fittings — above grade, below grade, and high-temp.	—
2	Here's how to install the Polyguard Wax Wrap system.	—
3	Step 1Prep the surface. Strip loose rust, dirt, and paint to an SP-2 hand-tool finish, then solvent-clean it.	"S-P two"
4	Step 2Brush Wax Primer over every surface you'll wrap: one to three mils, extended three inches past the wrap.	"one to three mils"
5	Step 3Press Profile Putty into the pits, angles, and voids. It softens with the heat of your hands and smooths the path for the tape.	—
6	Step 4Apply the Wax Wrap: start with a full overlap, then spiral it on with the overlap your job calls for.	—
7	Press out every air pocket and smooth the seams as you go.	—
8	Pro tipFinish with the end flaps facing down — it sheds water and shields the edges during backfill.	—
9	Step 5On flanges, tees, and fittings, leave a little slack so the wrap contours the shape, then smooth the seams to self-seal.	—
10	The result: a fully bonded, VOC-free, non-hazmat barrier you can backfill right away.	"V-O-C free"
11	Meets AWWA C217 and NACE 0375.	"A-W-W-A C two-seventeen … nace oh-three-seven-five"
12a	Off-sitePolyguard Wax Wrap. Learn more about the full system at Polyguard.com.	"Polyguard dot com"
12b	On-sitePolyguard Wax Wrap. Say yes to Polyguard.	—

2 Beats / Shot List

shot = 3D shot to render card = branded card logo = logo bumper. Ref = source clip the 3D shot + animatic frame are built from.

Beat	Kind	VO	3D shot	Top label	Ref clip @
01_logo	logo	1	Polyguard logo on black; faint pipe+tee silhouette resolves.	—	—
02_title	card	2	Title "HOW TO INSTALL · WAX WRAP SYSTEM"; bare steel pipe+tee+flanges slow-rotates; variant chips 60A grey · 60U brown · HT.	—	c3 / c2 0:00
03_prep	shot	3	Close on flange casting; wire-brush/grinder pass; rusty → clean steel.	SURFACE PREP · SSPC-SP2	c2 0:05–0:30
04_primer	shot	4	Gloved brush sweeps brown primer over every face of the casting; steel → brown; "+3 in" ghost band beyond the wrap zone.	WAX PRIMER · 1–3 MILS	c2 0:00–2:00
05_putty	shot	5	Putty pressed into angles / ribs / voids; chamfer fillets form; surface smooths.	PROFILE PUTTY · FILL VOIDS	c4 / c5
06_wrap	shot	6	Wax tape spiral-wraps a straight pipe leg; animated overlap %, full → spiral.	APPLY WAX WRAP · OVERLAP	c6 0:30–3:00
07_press	shot	7	Macro: gloved hand presses out an air pocket; seam smooths flat.	PRESS AIR OUT · SMOOTH SEAMS	c6
08_flaps	card	8	Clock diagram 3 → 9 o'clock; end flap rotates to face down; water droplets shed.	END FLAPS DOWN	c6 ~later
09_irregular	shot	9	Wrap contours the tee junction with slack; seams smoothed; self-seal glow.	FLANGES · TEES · FITTINGS	c7
10_result	shot	10	Finished fully-wrapped tee hero rotate; benefit chips VOC-FREE · NON-HAZMAT · IMMEDIATE BACKFILL.	—	c7 end
11_comply	card	11	Compliance badges: AWWA C217 · NACE 0375-2024. ✓ approved	—	—
12_cta_web	card	12a	Off-site outro (social/email/sales/YouTube): CTA "Learn more about the Wax Wrap system" · Polyguard.com.	—	—
12_cta_site	card	12b	On-site outro (PDP/shopping): brand lockup "Say yes to Polyguard" (no URL).	—	—

3 Accuracy Flags

✓ Variant = system (demo 60U brown; call out 60A grey + HT). ✓ AWWA / NACE approved on screen.
✓ On-screen label = "SSPC-SP2" (formal standard); VO says "S-P two".
✓ "Overlap your job calls for" stays true to both the 100%-then-≥1″ spec and the 50% demo.

4 Next Steps

Lock VO → generate Bryan's voice (explainer tts.py) → forced-align captions.
Storyboard frame per beat → assemble animatic via the explainer pipeline (9:16 first). Footage stands in for the 3D shots so pacing & narrative get approved before any render spend.
On approval: 3D artist renders each shot beat; AI-3D attempt per beat (benchmark, human vs AI).
Assemble masters in 9:16 / 16:9 / 1:1 + rendered stills / exploded diagrams.